Self-Powered Switch Technology

The Self-Powered Wireless Light Switch is the best solution for any light switch installation where running wires is difficult or expensive. Since the switch is wireless, it can be installed in minutes and it eliminates the need to cut holes into walls, install conduit, or fish wires.

The light switch requires no batteries or wires because of a built in micro-generator that creates a small amount of electricity every time the switch is pressed. This converted energy is used to power a transmitter that sends radio signals to controllers.

The following devices can be controlled by the Self-Powered Wireless Light Switch

Lights
Security systems
HVAC systems
Fans

Blinds
Lamps
Motors
Virtually any on/off device

Bluetooth Mesh Motion & Light Fixture Sensor

Part Number:

BTX-DUV-OCC

Description

The BTX-DUV-OCC is an Advanced Network Control for light fixtures that uses Bluetooth mesh communication for fixture to fixture grouping, wireless switch communication and mobile app based commissioning. The Fixture sensor is perfect for automatic lighting control in high or low bay applications with 2 lenses included for mount heights of 15-40 ft or 7-15 ft (2.5-15m) Each unit includes a light sensor for Daylight harvesting to minimize energy use when sufficient ambient light is available. Mobile apps for either iOS or Android allow configuration of operating parameters, grouping, and schedules. No gateway is needed as the Fixture Sensors communicate directly with the mobile app. The system uses encrypted communications with security credentials shared through QR Codes for either Admin or User access. No passwords, or web access is needed or supported. All configuration is performed with direct communication with the Fixture Sensor through the mobile app.

iOS and Android App based commissioning
Scene recall
Walk Test mode to confirm coverage area
Line voltage 0-10V dimming Advanced Network Control
- High end trim – adjust maximum light level
- Vacancy / Occupancy sensor to dim then turn off
- Fixture Grouping with Bluetooth mesh wireless communication
- Daylight harvesting
- Scheduling – time based on/off or scene recall

SPECIFICATIONS – **BTX-DUV-OCC**
Voltage Supply	120, 240, 277 VAC 50/60 Hz
Max Load	6 Amps, 600W for LED driver only 0-10V sink 20mA
Mounting Height	8-45 ft (2.5 – 15 m)
Approvals	UL8750 Safety FCC Part 15 IP65 – Dry or Damp Location Surge Protection L-N 1KV, L&N- PE 2KV
Dimensions	3.91’’ x 4.03’’ x 2.07’’
Operating Temperature	-40 to ~115 ºF (-40 to +45ºC)
Ambient Light Level Range	30-2500 Lux

Downloads

Bluetooth Mesh Motion / Light Fixture Sensor

Part Number:

BTX-D01-CCTFX

Description

The BTX-D01-CCTFX is an Advanced Network Control for light fixtures that uses Bluetooth mesh communication for fixture to fixture grouping, wireless switch communication and mobile app-based commissioning. The Fixture sensor is perfect for automatic lighting control in low bay applications 7-15 ft (2.5-5m) Each unit supports 2 channels of 0-20V dimming for controlling tunable white fixtures. It also includes a light sensor for Daylight harvesting to minimize energy use when sufficient ambient light is available. Mobile apps for either iOS or Android allow configuration of operating parameters, grouping, and schedules. No gateway is needed as the Fixture Sensors communicate directly with the mobile app. The system uses encrypted communications with security credentials shared through QR Codes for either Admin or User access. No passwords, or web access is needed or supported. All configuration is performed with direct communication with the Fixture Sensor through the mobile app.

iOS and Android App based commissioning
Scene recall
Walk Test mode to confirm coverage area
12VDC powered – Use w/ Dim to Off driver with Aux power output
0-10V CCT dimming Advanced Network Control
- High end trim – adjust maximum light level
- Vacancy / Occupancy sensor to dim then turn off
- Fixture Grouping with Bluetooth mesh wireless communication
- Daylight harvesting
- Scheduling – time based on/off or scene recall
- Color Tuning

**SPECIFICATIONS – BTX-D01-OCC**
Power	Input Voltage: 12 DC 35mA, Standby power: 0.45W
Max Load	0-10V sink 20mA No relay, requires Dim to Off driver
Motion Sensor	Mounting Height: 8-15 ft (2.5 – 5 m), Detection range: 48 ft max
Approvals	UL8750 Safety FCC Part 15
Dimensions	2.91 x 1.02 x 0.87 in (74 x 26 x 22 mm) Fixture Die Cut: 20.8 x 64.8mm
Environmental	-30 to ~131 ºF (-30 to +55ºC) Operating Temperature IP20
Ambient Light Level Range	30-2500 Lux

Downloads

Datasheet

Simple Lighting – Wireless & Battery-Free

Mobile Lighting Commissioning System

Description

The ILLUMRA Mobile Commissioning System includes an ILLUMRA Mobile Commissioning Gateway and the Scan & Link app, and is designed to support the installation of wireless controls from the planning phase to the completion of a project, and supports adjustments to behavior and zoning even after a project is complete.

Download the app on your iOS or Android smartphone.

Convenient Control

◼ Access and control ILLUMRA wireless controls from your smartphone

◼ Work as a team to plan, install, and configure behavior of lights and controls

◼ Connect to wireless controls by scanning a barcode, remote linking, discovering connected devices and more

◼ Easily program scenes, customize dimming levels, and create zones

Specifications
E9X-GWRC
Wireless Interface	802.11n Wireless LAN EnOcean 902MHz radio interface
Network Interface	Ethernet port (for remote updates) 802.11n Wireless LAN (for connection to mobile device)
Dimensions	3.6 x 2.9 x 0.9 inches

Downloads

Remotely Control Light Up to 300 Feet Away

Ever wished you had a conveniently located light switch that allowed you to turn off lights in a detached building, down a hall, or across a room? The ILLUMRA Relay Receiver + Repeater (part no.: E3X-R12-5IBBP) allows you to control lights from up to 300 feet away when used with ILLUMRA self-powered remote light switches and ILLUMRA receivers. The ILLUMRA Relay Receiver + Repeater can boost operating range 100% from the standard range of up to 150 feet or be used to transmit signals around objects. The device can be used in multiple ways to increase the capabilities of an ILLUMRA wireless control network.

First, the Relay Receiver + Repeater can be used to cover a greater distance. To do so, a Relay Receiver + Repeater is connected to power in between the location of an ILLUMRA wireless light switch and an ILLUMRA receiver. An ILLUMRA remote light switch can then transmit a signal to the Relay Receiver + Repeater; the device picks up the signals and rebroadcasts them up to an additional 150 feet.

Second, the Relay Receiver + Repeater can can be used to transmit a signal around objects. In environments that contain lots of metal or other obstructions, the device can help signals be transmitted at a less obstructed angle to an ILLUMRA receiver. For example, imagine that an ILLUMRA switch that controls two ILLUMRA receivers has been installed in front of a reinforced concrete wall with metal sheeting. Receiver A is to the right of the wall and Receiver B is behind the wall. In this scenario the signal transmitted by the ILLUMRA remote light switch may reach receiver A and control lights connected to receiver A. However, the signal may not penetrate the metal wall and reach receiver B. In this situation, a Relay Receiver + Repeater may be used to replace receiver A. When this is done, the system will work as follows: the signal transmitted by the remote light switch will be picked up by the Relay Receiver + Repeater, the lights connected to the Relay Receiver + Repeater will be controlled, and the device will re-transmit the wireless signal. The signal will effectively reach receiver B and control lights connected to receiver B.

The ILLUMRA Relay Receiver + Repeater can be used in both indoor and outdoor applications. Following are a few examples:

[one_half]

Indoor

Office Buildings
Warehouses
Schools
Hospitals
Retail Stores

[/one_half][one_half_last]

Outdoor

Detached Buildings
Stadiums
Parking Lots

[/one_half_last]

From office buildings to stadiums and more, the ILLUMRA Relay Receiver + Repeater provides users a quick and easy way to install convenient remote lighting controls for medium range applications. Simplify your project; try ILLUMRA controls today. Call (801) 349-1200 to find an ILLUMRA distributor near you.

Explore www.ILLUMRA.com to learn more about ILLUMRA Self-powered Wireless Controls.

Where To Buy v2

Illumra Distributors

USA

Canada

Newfoundland and Labrador

Northwest Territories

Nunavut

Not a distributor in your area? Call (801) 225-2226 and tell us your preferred supplier. We will try to expand ILLUMRA products into other stores.

Link Analyzer

Colors and Part Numbers

E3X-P30, E8X-P30

Description

The Link Analyzer allows specifiers and installers to plan, verify and maintain EnOcean based wireless networks. The hand-held analyzer is available in 315MHz and 868MHz versions.

The analyzer has four analyzer modes that test links, repeaters, and networks and also includes the ability to remotely control EnOcean based products. Power is supplied from two “AA” batteries. A wide range AC power supply, including a USB plug, comes with the P30, which allows long-term logging of the radio channel, including: timing, signal strength, and packet data.

Specifications
E3X-P30 \| E8X-P30
Batteries	2 x “AA” batteries
Power Supply	Battery or external power supply
Frequency	315 MHz or 868 MHz

Downloads

Applications

Coming Soon

Wiring Diagrams

Coming Soon

Application Notes

Private Label Forms

Private Labeling

All our products are available with your logo, so you can bundle wireless controls to sell with your fixtures.

With no effort on your part–once you’re set up–products will be shipped with your logo on the label and shipping box. The mobile app will show your logo. Setting this up is easy.

How to use the OEM Label Forms for the xUV Product Line

This document is intended to help you make labels for the Area Controller, Fixture Controller, 20 Amp Universal Relay, and Control Extender.

In order to use the OEM label form, you should first collect the following information.

The name and contact information of the person who will approve the artwork.
The ordering code you will use when selling the product.
The product details you want listed near the logo, applied to the front label as well as the box.
Your logo. It will be printed at 300dpi in a space that is .95 inches x .285 inches, or 285 x 86 pixels (W x L). The logo image should be monochrome.

The information highlighted in yellow below is the information you can customize using this form. This is an example of our area controller label.

Once you have collected the requested information, you will go to the form of the label you wish to customize.

The links are listed below:

Area Controller

Fixture Controller

20 Amp Universal Relay

Control Extender

Once all the requested information has been submitted and the logo received, we will make a digital mock up for you to approve. Once the label and artwork has been approved we will be able to use your custom label on the product.

Download this information.

600 Watt Phase Cut Dimming Controller

Part Number

E9X-ER6CD or E9X-ER6CD-277

Description

The ILLUMRA 600 W Phase Cut Dimming Controller supports forward or reverse phase dimming.

“The E9X-ER6CD is a phase adaptive line voltage lighting controller that automatically provides reverse or forward phase dimming based on the connected load type. The dimmer makes upgrading to a hybrid lighting system easy, by offering phase-adaptive, line voltage dimming for tungsten, two-wire fluorescent, line-voltage LED, and electronic low-voltage transformer loads (120V only).”

Use as part of a wireless control system to reduce energy consumption or to implement compliance with the latest energy regulations.

Reverse or forward phase single-channel 600 Watt dimming
Integrated daylight harvesting control with Photo Inhibit feature
Easy installation on electrical junction boxes with 1/2 ” mounting nipple
Doubles as a telegram repeater

Features

Phase adaptive dimming. Provides reverse or forward dimming based on connected load type.
Central Command support. For BACnet Management System control
Interoperable. Communicates wirelessly with other devices using the EnOcean wireless standard.

Dimensions

Wiring Diagram

Specifications

	E9X-ER6CD or E9X-ER6CD-277
Power Supply	120 VAC or 277 VAC @ 50/60Hz
Power Consumption	Min. 1 W load – Max. 600 W load • Tungsten • 2-wire Fluorescent • Line voltage LED • Electric low voltage transformer (120V only)
RF Communications	EnOcean® Protocol 902 MHz
EEP (EnOcean Equipment Profile)	F6-02-02 (Light and Blinds Control – US/Canada application) A5-06-02 (Light Sensor [range 0 – 1024 lux ]) A5-07-01 (Occupancy Sensor) A5-38-08 (Central command, switching, dimming and set point)
Transmission Range	50-150 feet (typical)
Operational Temperature	CSA: 32ºF to 104ºF (0ºC to 40ºC) UL: 32ºF to 122ºF (0ºC to 50º C)
Relative Humidity	5% to 95% RH (non-condensing)
Dimensions	3.5 x 3.1 x 1.9 inches (89 x 78 x 47 mm)
Agency Compliance	ETL, UL, FCC, & IC compliant

Downloads

Datasheet

20A 0-10V Dimming Area Controller

Part Number

E9X-DUV-10VTP

Description

The 20A 0-10V Dimming Area Controller from ILLUMRA allows wireless control of room ambiance by dimming LED and fluorescent luminaries. The controller also reduces energy consumption and supports compliance with the latest energy regulations.

The controller is rated for switching full 20A circuits, allowing it to work in nearly any application.

Area vs. Fixture Controller

The Area Controller on this page features full 20A circuit switching capacity and may be used to control multiple fixtures over a larger area by daisy-chaining the 0-10V control signals between fixtures.

To control multiple fixtures without daisy-chaining 0-10V control wires, see the 5A 0-10V Dimming Fixture Controller, which is optimized for use one controller per fixture to eliminate the need for adding dimming control wiring between fixtures.

Specifications	E9X-DUV-10VTP
Supply Voltage	100-277 VAC 50 – 60Hz
Maximum Load:	20 Amps Resistive, Induction, Fluorescent, LED, Other
	160A Max Inrush Current
	0-10V sink 100mA (IEC Standard 60929 Annex E)
	0-10V source 1mA (ANSI E1.3-2001 R2011)
Compatible Loads	Metal Halide; Sodium Vapour; LED; Induction; Fluorescent; Other
Range	50-150 feet (typical)
Frequency	902MHz EnOcean® Protocol
Dimensions	2.11 x 1.73 x 1.09 inches (54 x 44 x 28 mm)
Operating Temperature:	+32° to +122°F (0° to +50°C)
Storage Temperature:	-4° to +176°F (-20° to +80°C)
Memory Storage	20 links
Transmit EEP	A5-38-08
Approvals	UL 60730 (safety); UL 2043 (plenum); CSA c22.2#14-05 (safety); CE – IEC 60730; FCC: SZV-STM300U IC: 5713A-STM300U

Downloads

Applications

Conference rooms
Houses of worship
Classrooms
Offices
Daylight harvesting
Load Shedding

Wiring Diagrams

5A 0-10V Dimming Fixture Controller

Part Number

E9X-DUV-10VTP-FX

Description

The 5A 0-10V Dimming Fixture Controller from ILLUMRA allows wireless control of room ambiance by dimming LED and Fluorescent Luminaries. The controller reduces energy consumption through the use of manual control, vacancy detection, daylighting, load shedding strategies enabled with wireless connections to accessories such as wireless motion sensors, light sensors, switches, etc. The fixture controller provides a compelling, cost effective, minimally disruptive solution for compliance with the latest energy regulations.

Fixture vs. Area Controller

The 5A Fixture Controller on this page is optimized for use one per fixture to eliminate the need for adding control wiring between fixtures.

The 20A Area Controller features full 20A circuit switching capacity and may be used to control multiple fixtures over a larger area by daisy-chaining the 0-10V control signals between fixtures.

Specifications	E9X-DUV-10VTP-FX
Supply Voltage	100-277VAC 50 /60 Hz
Maximum Load:	5 AMPs all loads; 0-10V sink 100mA; 0-10V source 1mA 70A Max Inrush Current
Load Type:	Metal Halide; Sodium Vapor; Induction; Fluorescent; LED; Other
Range	50-150 feet (typical)
Frequency	902 MHz EnOcean® Protocol
Dimensions:	2.11 x 1.73 x 1.09 inches (54 x 44 x 28 mm)
Operating Temperature:	+32° to +122°F (0° to +50°C)
Storage Temperature:	-4° to +176°F (-20° to +80°C)
Approval
	UL 60730 (safety)
	UL 2043 (plenum)
	CSAc22.2#14-05 (safety)
	CE – IEC 60730
	FCC: SZV-STM300U IC: 5713A-STM300U

Downloads

Applications

Conference Rooms
Houses of Worship
Classrooms
Offices
Daylight harvesting
Load Shedding

Wiring Diagrams

5A On/Off Fixture Controller

Part Number

E9X-RUV-3HOTP

Description

The ILLUMRA 5A On/Off Fixture Controller is a line-voltage controller that allows lights to be controlled by ILLUMRA self-powered switches, occupancy sensors, light sensors, and gateways to implement power saving strategies.

Use as part of a wireless control system to reduce energy consumption or to implement compliance with the latest energy regulations.

Features

On/Off control for individual LED and fluorescent luminaries and other 5A loads
Reduce energy consumption
Extend equipment life

For larger load ratings, see the 20A On/Off Area Controller.

For dimming control, see the 5A Dimming Fixture Controller and the 20A Dimming Area Controller.

Specifications	E9X-RUV-3HOTP
Supply Voltage	100-277 VAC 50/60 Hz
Max Load	5A all loads, Induction, Fluorescent, LED, Other 70A Max Inrush Current 1/4HP
RF Communication	902 MHz EnOcean® Protocol
Transmission Range	50-150 feet (typical)
Dimensions	2.61 x 1.73 x 1.09 inches (66 x 44 x 28mm)
Operating Temperature	+32º to +122ºF (0 to +50ºC)
Storage Temperature	-4° to +176°F (-20° to +80°C)
Approvals	UL 60730 (safety) UL 2043 (plenum) CSA c22.2#14-05 (safety) CE – IEC 60730 FCC ID: SZV-STM300U IC ID: 5713A-STM300U

Compatible Devices:

Wireless Light Switches
Key Card Switch
Control Transmitter
Wireless Occupancy Sensors
Window/Door Sensor
Light Sensor
Gateway

Downloads

Applications

Remote Switching
Re-zoning without rewiring
Class Rooms
Daylight harvesting
Load shedding

Wiring Diagrams

E9X-RUV-3HOTP Wiring Diagram
120 V Wireless 3-Way Switch

Single Rocker Wireless Light Switch

Colors and Part Numbers

White…………………E9T-S1AWH

Light Almond……..E9T-S1ALA

Ivory…………………..E9T-S1AIV

Gray…………………..E9T-S1AGY

Brown………………..E9T-S1ABR

Black………………….E9T-S1ABK

Description

ILLUMRA Self-Powered Wireless Light Switches are completely wireless and battery-free. They use the kinetic energy from pressing the switch to send a wireless RF signal to controllers and gateways.

Control a light fixture or one group of lights with this ILLUMRA Single Rocker Switch. This switch communicates with 902 MHz EnOcean protocol. Switches are also available in ZigBee and Bluetooth protocols. Accelerate installation of wireless controls from the planning phase to the completion with our new mobile commissioning system.

Specifications
E9T-S1Axx
Range	50-150 feet (typical)
Frequency	902 MHz EnOcean® Protocol
Power Supply	Self-generated when switch is pressed
Buttons	2 Buttons (1 rocker)
Output Channels	Only limited by number of receivers in range
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature [Storage Temperature]	-13° to +149°F (- 25° to + 65°C) [-13° to +149°F (- 25° to + 65°C)]
Radio Certifications	FCC (United States): SZV-PTM215U I.C. (Canada): 5713A-PTM215U
Addressing	Factory set unique ID (1 of 4 billion)

Downloads

Applications

Wiring Diagrams

Dual Rocker Self Powered Wireless Light Switch

Colors and Part Numbers

White………………..E9T-S2AWH

Black…………………E9T-S2ABK

Light Almond………E9T-S2ALA

Ivory…………………..E9T-S2AIV

Gray …………………..E9T-S2AGY

Brown…………………E9T-S2ABR

Description

ILLUMRA Self-Powered Wireless Light Switches are completely wireless and battery-free. They use the kinetic energy from pressing the switch to send a wireless RF signal to controllers and gateways.

Control two lights or two groups of lights with this ILLUMRA Dual Rocker Light Switch. Each rocker can separately control an unlimited number of ILLUMRA controllers that are within range.

This switch communicates with 902 MHz EnOcean protocol. Switches are also available in ZigBee and Bluetooth protocols. See also our Single Rocker Switch.

Accelerate installation of wireless controls from the planning phase to the completion with our new mobile commissioning system.

**Specifications**
E9T-S2Axx
Range	50-150 feet (typical)
Frequency	902MHz
Power Supply	Self-generated when switch is pressed
Buttons	4 Buttons(2 rockers)
Output Channels	Only limited by number of receivers in range
Dimensions	2.75(W) x 4.5(H) x 0.62(D)inches
Operating Temperature [Storage Temperature]	-13° to +149°F (- 25° to + 65°C) [-13° to +149°F (- 25° to + 65°C)]
Radio Certifications	FCC (United States): SZV-PTM215U I.C. (Canada):5713A-PTM215U
Addressing	Factory set unique ID(1 of 4 billion)

Downloads

Applications

Wiring Diagrams

ILLUMRA

New Site!

Welcome to ILLUMRA’s new site! We hope that you find the site easy to navigate and understand. We are happy to introduce new layouts and updates to our information. One notable layout change is our individual products page. This page has all of the product information in one, simple tabulated area. Click on the tabs to see relevant information to the product such as its description, specifications, colors and part numbers, and more!

Please visit our “Contact Us” page for easy contact forms to send us any information about our products or site that we need to fix and update.

Enjoy!

Self-Powered Single Rocker ZigBee Wireless Light Switch

Part Number

ZBT-S1AWH (single rocker, white)

Order ZigBee switches right now from Digikey:

Single Rocker ZigBee Switch

Or request a quote from ILLUMRA, using the form below.

Description

The Self-Powered ZigBee Switch is a wireless transmitter that communicates with a wide variety of ZigBee compatible systems. The switch uses battery-free, energy harvesting technology. Every time the switch is pressed a micro-generator produces a small electrical current that powers a built-in transmitter. This transmitter sends wireless radio signals that are used to remotely control a compatible system.

Specifications
ZBT-S1AWH
Range	30-100 ft or 10-30 m (typical)
Frequency	2.4 GHz (ZigBee channels 11-26)
Power Supply	Self-generated when switch is pressed
Buttons	2 Buttons (1 rocker)
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature	-13° to +149°F (- 25° to + 65°C)
Radio Certifications	Certified according to FCC and IC and CE regulations
Addressing	Factory set unique ID

Downloads

Applications

Philips EasySense

Wireless PIR and Light Sensor

Part Number

E9T-OBP

Description

The ILLUMRA™ Puck Sensor is a battery powered motion and light sensor with versatile mounting options that include: ceiling, wall and free-standing.

Designed to pair to building management devices using the 902MHz ILLUMRA products. The motion time out is adjustable at the sensor when used with compatible receivers.

Specifications	E9T-OBP Model
Detection Dist.	Ceiling Mount: 20’dia@8’ ceiling height Wall, Desk top: 16’rad. X 120°
Frequency	902 MHz EnOcean Protocol
Radio Range	100’ max @ +3dbM
Power Supply	(1) CR123A 3V Battery, 5yr Life
Ambient Light	0-1000 Lux potentiometer
Output Channels	Stand Alone – Direct control of devices Gateway – Notifies GW of detection
Dimensions	2.56” x 2.56” x 1.5” [65x65x39mm]
Amb. Op. Temp.	14°F to 113°F [-10°C to +45°C]
Certifications	FCC

Downloads

Ceiling Occupancy Sensor

Part Number

E9T-OSC

Description

Ceiling-Mount Motion Sensors sense motion over a 360 degree coverage area.

Specifications	E9T-OSC
Frequency	902 MHz EnOcean RF transmitter
Transmission Range	50-100 ft. (17-33M)
Motion Detection Range	34ft. (10m) diameter @ 10ft (3m) mounting height (Refer to coverage diagrams)
Minimum Operation Light	50 lux (for auto-off only)
Charge time to full	25 hrs @200 lux
Sustaining Charge time	3 hours per 24 hours @ 200 lux
Motion Transmission Interval	2 minutes
Unoccupied Transmission	10 and 30 minutes since last motion detection
Heartbeat Transmission	default = disable / enable = 1 hr intervals
Operating Life in Darkness	80 hours (after full charge)
Optional Battery Life	Continuous battery-free operation standard; Infrequent Bright Light: 20yrs (with 200lux for 2 hrs/day 7days/week Consistent Low Light: 15 yrs (with 65 lux for 5 hrs/day 7 days/week Total Darkness: 6.5 yrs
EnOcean Equipment Profile (EEP)	A5-07-01
Dimensions	6.5″ H x 2.36″ W x 1.47″ D (160mm x 60mm x 37mm)
Mounting Height	7-10 feet (2-3m) recommended
Agency Compliance	FCC: SZV-STM300U

Downloads

Applications

Coming Soon

Wiring Diagrams

Coming Soon

Wireless LED Dimmer Demonstration Kit

[three_fourth_last][one_third]

[box]

Wireless LED Dimmer Demo Kit

[/box]

Wireless LED Dimmer Demo Kit:

ExT-S1AWH – Single Rocker Switch

E9X-D02FL – Wireless Receiver

ExT-OSW-W – Wall Occupancy Sensor

[/one_third]

[two_third_last]

[box]Description

Experience PWM LED dimming control with a battery-free wireless switch and an occupancy sensor. Energy harvesting switches and sensors harvest mechanical and ambient light energy to operate without batteries. The PWM LED Dimmer switches 5A loads with 65,000 smooth dimming steps.

A Wireless 0-10V Dimmer Demo Kit is also available.[/box]

[table “” not found /]

[one_third]
Downloads

Switch Datasheet
Switch Installation Guide
Constant Voltage Dimmer
Constant Voltage Installation Guide[/one_third][one_third]

Applications

Commercial Lighting Control
Title 24 Wireless Lighting Control
Log Home Lighting
Landscape Lighting
(More . . .)[/one_third][one_third_last]

Wiring Diagrams

[/one_third_last][/two_third_last]

Wireless 0-10V Dimmer Demonstration Kit

[one_third]

[box]

Wireless 0-10V Dimmer Demo Kit

[/box]

Wireless 0-10V Dimmer Demo Kit:

ExT-S1AWH – Single Rocker Switch

E9X-DUV-10VTP – Wireless Area Controller

ExT-OSW-W – Wall Occupancy Sensor

[box]See Wireless LED Dimmer Demo Kit
[/box]

[/one_third]

[two_third_last]

[box]Description

Experience a 0-10V dimming control with a battery-free wireless switch and an occupancy sensor. Energy harvesting switches and sensors harvest mechanical and ambient light energy to operate without batteries. The 0-10V Area Controller switches 20A loads and dims up to 150 fixtures.

A PWM LED Dimmer Demonstration kit is also available.
[/box]

[table “” not found /]

[one_third]
Downloads

Switch Datasheet
Switch Installation Guide
Occupancy Sensor Datasheet
Occupancy Sensor Installation Guide
Receiver Datasheet
Receiver Installation Guide[/one_third][one_third]

Applications

Commercial Lighting Control
Title 24 Wireless Lighting Control
Log Home Lighting
Landscape Lighting
(More . . .)[/one_third][one_third_last]

Wiring Diagrams

[/one_third_last][/two_third_last]

Self-Powered Single Rocker ZigBee Wireless Light Switch

Part Number

ZBT-S1AWH (single rocker, white)

.

Request a quote by using the form below.

Description

The Self-Powered ZigBee Switch is a wireless transmitter that communicates with a wide variety of ZigBee compatible systems. The switch uses battery-free, energy harvesting technology. Every time the switch is pressed a micro-generator produces a small electrical current that powers a built-in transmitter. This transmitter sends wireless radio signals that are used to remotely control a compatible system.

Specifications
ZBT-S1AWH
Range	30-100 ft or 10-30 m (typical)
Frequency	2.4 GHz (ZigBee channels 11-26)
Power Supply	Self-generated when switch is pressed
Buttons	2 Buttons (1 rocker)
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature	-13° to +149°F (- 25° to + 65°C)
Radio Certifications	Certified according to FCC and IC and CE regulations
Addressing	Factory set unique ID

Downloads

Applications

Philips EasySense

Bluetooth Switch

Part Numbers

BTT-S1AWH (single rocker, white)

BTT-S2AWH (dual rocker, white)

Description

The self-powered Bluetooth Switch is a wireless transmitter that communicates with a wide variety of Bluetooth compatible systems. The switch uses battery-free, energy harvesting technology. Every time the switch is pressed a micro-generator produces a small electrical current that powers a built-in transmitter. This transmitter sends wireless radio signals that are used to remotely control a compatible system.

Also available in ZigBee and EnOcean.

Specifications
BTT-S1AWH \| BTT-S2AWH
Range	30-100 ft or 10-30 m (typical)
Frequency	Bluetooth 2.4 GHz
Power Supply	Self-generated when switch is pressed
Buttons	2 Buttons (1 rocker) \| 4 Buttons (2 rockers)
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature	-13° to +149°F (- 25° to + 65°C)
Radio Certifications	Certified according to FCC and IC and CE regulations
Addressing	Factory set unique ID

Downloads

Request a Quote form:

SPECIFICATIONS – BTX-DUV-OCC

Request a Quote form:

SPECIFICATIONS – BTX-D01-OCC

Request a Quote form:

Illumra Distributors

USA

Canada

Request a Quote form:

Private Labeling

All our products are available with your logo, so you can bundle wireless controls to sell with your fixtures.

With no effort on your part–once you’re set up–products will be shipped with your logo on the label and shipping box. The mobile app will show your logo. Setting this up is easy.

How to use the OEM Label Forms for the xUV Product Line

This document is intended to help you make labels for the Area Controller, Fixture Controller, 20 Amp Universal Relay, and Control Extender.

In order to use the OEM label form, you should first collect the following information.

The name and contact information of the person who will approve the artwork.

The ordering code you will use when selling the product.

The product details you want listed near the logo, applied to the front label as well as the box.

Your logo. It will be printed at 300dpi in a space that is .95 inches x .285 inches, or 285 x 86 pixels (W x L). The logo image should be monochrome.

The information highlighted in yellow below is the information you can customize using this form. This is an example of our area controller label.

Once you have collected the requested information, you will go to the form of the label you wish to customize.

The links are listed below:

Once all the requested information has been submitted and the logo received, we will make a digital mock up for you to approve. Once the label and artwork has been approved we will be able to use your custom label on the product.

Request a Quote form:

Features

Dimensions

Wiring Diagram

Specifications

Request a Quote form:

Area vs. Fixture Controller

Request a Quote form:

Fixture vs. Area Controller

Request a Quote form:

Request a Quote form:

Specifications

Request a Quote form:

Featured Products

Self-Powered Wireless Light Switch

ILLUMRA Self-Powered Wireless Light Switches are completely wireless and battery-free. This offers unique flexibility in installation.

Room and Area Controllers

The ILLUMRA 20A On/Off Area Controller switches full circuit 20 amp loads on command from wireless switches, sensors, and central controllers to facilitate the reduction of energy consumption and support compliance with the latest energy regulations.

SAVE MONEY

Energy Savings

Fast Installation

Unique Applications

GREEN ENERGY

Energy Harvesting

Self-Powered and Wireless

Energy Code Compliance

FLEXIBLE INTEGRATION

Easy Configuration

Wireless Internet of Things

Building Management System Integration

Request a Quote

Order ZigBee switches right now from Digikey:

Or request a quote from ILLUMRA, using the form below.

Request a Quote form:

Request a Quote form:

Request a Quote form:

Request a Quote form:

Request a Quote form:

Request a quote by using the form below.

Request a Quote form:

Request a Quote form:

Specifications