Wireless Plant Controls

ILLUMRA wireless plant controls

ILLUMRA wiring diagrams

3 Phase Motor Controller Using LVRX-4 (E3R-R04FP-4)

Application

Extend the capability of a control station by adding a additional control locations.

Scenario

A 3-phase motor needed to be started and stopped from multiple locations within a plant. The control system needed to interface with the existing magnetic starter, commonly found on such motors. Running wires to the additional control locations would have been expensive and time-consuming.

Solution

Plant engineers selected ILLUMRA wireless controls to add additional control locations to the existing motor and its magnetic starter. Installing the ILLUMRA system was completed in less than 1 hour, saving weeks of time and eliminating the need to use costly construction materials. ILLUMRA self-powered controls are ideal for applications like this, because they don’t require ongoing maintenance and can be installed virtually anywhere.

Products

Single Rocker Switch	Low Voltage Relay Receiver

Link Analyzer

Colors and Part Numbers

E3X-P30, E8X-P30

Description

The Link Analyzer allows specifiers and installers to plan, verify and maintain EnOcean based wireless networks. The hand-held analyzer is available in 315MHz and 868MHz versions.

The analyzer has four analyzer modes that test links, repeaters, and networks and also includes the ability to remotely control EnOcean based products. Power is supplied from two “AA” batteries. A wide range AC power supply, including a USB plug, comes with the P30, which allows long-term logging of the radio channel, including: timing, signal strength, and packet data.

Specifications
E3X-P30 \| E8X-P30
Batteries	2 x "AA" batteries
Power Supply	Battery or external power supply
Frequency	315 MHz or 868 MHz

Downloads

Applications

Coming Soon

Wiring Diagrams

Coming Soon

Bluetooth Mesh Motion & Light Fixture Sensor

Part Number:

BTX-DUV-OCC

Description

The BTX-DUV-OCC is an Advanced Network Control for light fixtures that uses Bluetooth mesh communication for fixture to fixture grouping, wireless switch communication and mobile app based commissioning. The Fixture sensor is perfect for automatic lighting control in high or low bay applications with 2 lenses included for mount heights of 15-40 ft or 7-15 ft (2.5-15m) Each unit includes a light sensor for Daylight harvesting to minimize energy use when sufficient ambient light is available. Mobile apps for either iOS or Android allow configuration of operating parameters, grouping, and schedules. No gateway is needed as the Fixture Sensors communicate directly with the mobile app. The system uses encrypted communications with security credentials shared through QR Codes for either Admin or User access. No passwords, or web access is needed or supported. All configuration is performed with direct communication with the Fixture Sensor through the mobile app.

iOS and Android App based commissioning
Scene recall
Walk Test mode to confirm coverage area
Line voltage 0-10V dimming Advanced Network Control
- High end trim - adjust maximum light level
- Vacancy / Occupancy sensor to dim then turn off
- Fixture Grouping with Bluetooth mesh wireless communication
- Daylight harvesting
- Scheduling - time based on/off or scene recall

SPECIFICATIONS - **BTX-DUV-OCC**
Voltage Supply	120, 240, 277 VAC 50/60 Hz
Max Load	6 Amps, 600W for LED driver only 0-10V sink 20mA
Mounting Height	8-45 ft (2.5 - 15 m)
Approvals	UL8750 Safety FCC Part 15 IP65 - Dry or Damp Location Surge Protection L-N 1KV, L&N- PE 2KV
Dimensions	3.91’’ x 4.03’’ x 2.07’’
Operating Temperature	-40 to ~115 ºF (-40 to +45ºC)
Ambient Light Level Range	30-2500 Lux

Downloads

Bluetooth Mesh Motion / Light Fixture Sensor

Part Number:

BTX-D01-CCTFX

Description

The BTX-D01-CCTFX is an Advanced Network Control for light fixtures that uses Bluetooth mesh communication for fixture to fixture grouping, wireless switch communication and mobile app-based commissioning. The Fixture sensor is perfect for automatic lighting control in low bay applications 7-15 ft (2.5-5m) Each unit supports 2 channels of 0-20V dimming for controlling tunable white fixtures. It also includes a light sensor for Daylight harvesting to minimize energy use when sufficient ambient light is available. Mobile apps for either iOS or Android allow configuration of operating parameters, grouping, and schedules. No gateway is needed as the Fixture Sensors communicate directly with the mobile app. The system uses encrypted communications with security credentials shared through QR Codes for either Admin or User access. No passwords, or web access is needed or supported. All configuration is performed with direct communication with the Fixture Sensor through the mobile app.

iOS and Android App based commissioning
Scene recall
Walk Test mode to confirm coverage area
12VDC powered - Use w/ Dim to Off driver with Aux power output
0-10V CCT dimming Advanced Network Control
- High end trim - adjust maximum light level
- Vacancy / Occupancy sensor to dim then turn off
- Fixture Grouping with Bluetooth mesh wireless communication
- Daylight harvesting
- Scheduling - time based on/off or scene recall
- Color Tuning

**SPECIFICATIONS - BTX-D01-OCC**
Power	Input Voltage: 12 DC 35mA, Standby power: 0.45W
Max Load	0-10V sink 20mA No relay, requires Dim to Off driver
Motion Sensor	Mounting Height: 8-15 ft (2.5 - 5 m), Detection range: 48 ft max
Approvals	UL8750 Safety FCC Part 15
Dimensions	2.91 x 1.02 x 0.87 in (74 x 26 x 22 mm) Fixture Die Cut: 20.8 x 64.8mm
Environmental	-30 to ~131 ºF (-30 to +55ºC) Operating Temperature IP20
Ambient Light Level Range	30-2500 Lux

Downloads

Datasheet

Application Notes

Private Label Forms

Private Labeling

All our products are available with your logo, so you can bundle wireless controls to sell with your fixtures.

With no effort on your part–once you’re set up–products will be shipped with your logo on the label and shipping box. The mobile app will show your logo. Setting this up is easy.

How to use the OEM Label Forms for the xUV Product Line

This document is intended to help you make labels for the Area Controller, Fixture Controller, 20 Amp Universal Relay, and Control Extender.

In order to use the OEM label form, you should first collect the following information.

The name and contact information of the person who will approve the artwork.
The ordering code you will use when selling the product.
The product details you want listed near the logo, applied to the front label as well as the box.
Your logo. It will be printed at 300dpi in a space that is .95 inches x .285 inches, or 285 x 86 pixels (W x L). The logo image should be monochrome.

The information highlighted in yellow below is the information you can customize using this form. This is an example of our area controller label.

Once you have collected the requested information, you will go to the form of the label you wish to customize.

The links are listed below:

Area Controller

Fixture Controller

20 Amp Universal Relay

Control Extender

Once all the requested information has been submitted and the logo received, we will make a digital mock up for you to approve. Once the label and artwork has been approved we will be able to use your custom label on the product.

Download this information.

Mobile Lighting Commissioning System

Description

The ILLUMRA Mobile Commissioning System includes an ILLUMRA Mobile Commissioning Gateway and the Scan & Link app, and is designed to support the installation of wireless controls from the planning phase to the completion of a project, and supports adjustments to behavior and zoning even after a project is complete.

Download the app on your iOS or Android smartphone.

Convenient Control

◼ Access and control ILLUMRA wireless controls from your smartphone

◼ Work as a team to plan, install, and configure behavior of lights and controls

◼ Connect to wireless controls by scanning a barcode, remote linking, discovering connected devices and more

◼ Easily program scenes, customize dimming levels, and create zones

Specifications
E9X-GWRC
Wireless Interface	802.11n Wireless LAN EnOcean 902MHz radio interface
Network Interface	Ethernet port (for remote updates) 802.11n Wireless LAN (for connection to mobile device)
Dimensions	3.6 x 2.9 x 0.9 inches

Downloads

Where To Buy v2

Illumra Distributors

USA

Canada

Newfoundland and Labrador

Northwest Territories

Nunavut

Not a distributor in your area? Call (801) 225-2226 and tell us your preferred supplier. We will try to expand ILLUMRA products into other stores.

ILLUMRA’s Controls Honored in New York City’s Green Technology Initiative

ILLUMRA, a leader in lighting control and energy management systems, announced selection by New York City’s Municipal Entrepreneurial Testing System (METS). The pilot program includes two of ILLUMRA’s products, the self-powered wireless occupancy sensor, and the M3 wireless steam valve control. The wireless products save energy, time and money and are designed to install in as little as 20 minutes with minimal disruption to building operations. The systems will be installed in various city buildings, where cost savings will be monitored and evaluated for wider deployment within the city.

CMR “We’re excited to be chosen by the METS program and look forward to the opportunity to show how our wireless control products can save New York City both time and money,” said Jan Finlinson, ILLUMRA CEO. “Our unique green technology can be retrofitted economically and easily in any government or commercial building.”

METS is a NY city partnership of Speaker Christine C. Quinn, Council Member Michael Nelson, the Department of Citywide Administrative Services (DCAS) and the New York City Housing Authority (NYCHA), to promote green technologies in city buildings. In addition to the METS initiative, ILLUMRA will be highlighting its latest lighting control products at the LIGHTFAIR International tradeshow and conference in Las Vegas, Nevada on May 9-11 (EnOcean Alliance Booth # 612).

About ILLUMRA

ILLUMRA is a leading North American supplier of lighting control and energy management systems. ILLUMRA is an EPA Energy Star Partner and develops wired and wireless HVAC and lighting controls for commercial buildings. Products are sold via dealers and OEM partners throughout the world. For more information about ILLUMRA and its products, please visitwww.ILLUMRA.com, or call (801) 349-1200.

###

ILLUMRA Self-powered Wireless ControlsSelected For “2012 Top Products Award Winners”

ILLUMRA Self-powered Wireless Door sensor Selected For “2012 Top Products Award Winners”

Wireless Window/Door sensor receives top honors

ILLUMRA Self-powered Wireless Controls of Lindon, UT has been honored with a recognition by Building Operating Management in its selection of “2012 Top Products Award Winners.”

Lindon, UT November 1, 2012– Announcing a special recognition appearing in the January, 2012 issue of Building Operating Management. The Self-powered Wireless Window/Door sensor from ILLUMRA was selected for the following honor:

“2012 Top Products Award Winners”

The Wireless Window/Door sensor is used to reduce energy consumption and equipment wear and tear in hotel rooms, condominiums, schools, and etc. by shutting off air conditioning equipment when Windows or Doors are open. The wireless sensor transmits radio frequencies to eliminate the time and cost of installing wires to the sensor. Additionally, the wireless door sensor reduces maintenance cost because it does not require batteries; instead it uses energy collected from ambient indoor light using small solar cell stores enough energy to operate for several days in complete darkness.

Jan Finlinson, Director from ILLUMRA Self-powered Wireless Controls commented on the recognition: “The fact that Building Operating Management included ILLUMRA Self-powered Wireless Controls in its selection of “2012 Top Products Award Winners,” signals that our constant efforts towards business excellence are paying off. We are proud to be included in this recognition.”

For more information on ILLUMRA Self-powered Wireless Controls, located in Lindon, UT please call 801-349-1200.

Contact Info:

ILLUMRA Self-powered Wireless Controls

Phone: 801-349-1200

Email Address: [email protected]

ILLUMRA Self-powered Wireless Controls Selected For “2012 Top Products Award Winners”.

Become a Rep

Become a Distributor

Press

Distribution

Self-Powered Single Rocker ZigBee Wireless Light Switch

Part Number

ZBT-S1AWH (single rocker, white)

Order ZigBee switches right now from Digikey:

Single Rocker ZigBee Switch

Or request a quote from ILLUMRA, using the form below.

Description

The Self-Powered ZigBee Switch is a wireless transmitter that communicates with a wide variety of ZigBee compatible systems. The switch uses battery-free, energy harvesting technology. Every time the switch is pressed a micro-generator produces a small electrical current that powers a built-in transmitter. This transmitter sends wireless radio signals that are used to remotely control a compatible system.

Specifications
ZBT-S1AWH
Range	30-100 ft or 10-30 m (typical)
Frequency	2.4 GHz (ZigBee channels 11-26)
Power Supply	Self-generated when switch is pressed
Buttons	2 Buttons (1 rocker)
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature	-13° to +149°F (- 25° to + 65°C)
Radio Certifications	Certified according to FCC and IC and CE regulations
Addressing	Factory set unique ID

Downloads

Applications

Philips EasySense

Wireless PIR and Light Sensor

Part Number

E9T-OBP

Description

The ILLUMRA™ Puck Sensor is a battery powered motion and light sensor with versatile mounting options that include: ceiling, wall and free-standing.

Designed to pair to building management devices using the 902MHz ILLUMRA products. The motion time out is adjustable at the sensor when used with compatible receivers.

Specifications	E9T-OBP Model
Detection Dist.	Ceiling Mount: 20’dia@8’ ceiling height Wall, Desk top: 16’rad. X 120°
Frequency	902 MHz EnOcean Protocol
Radio Range	100’ max @ +3dbM
Power Supply	(1) CR123A 3V Battery, 5yr Life
Ambient Light	0-1000 Lux potentiometer
Output Channels	Stand Alone - Direct control of devices Gateway - Notifies GW of detection
Dimensions	2.56” x 2.56” x 1.5” [65x65x39mm]
Amb. Op. Temp.	14°F to 113°F [-10°C to +45°C]
Certifications	FCC

Downloads

Wireless 0-10 Volt Primary and Secondary Dimming Controller Tutorial

Demonstration of ILLUMRA 0-10V Primary / Secondary (Master / Slave) remote LED dimmer controls. Also shows battery-free wireless switches and occupancy sensors being linked to wireless 0-10V Area Controllers. The Area Controller features 20A load switching capacity and 0-10V dimming circuit rated to control dimming of up to 200 fixtures. The system uses wireless motion sensors to operate occupancy sensing mode with the lights turning on with motion or in vacancy mode with a manual switch and lights turning off automatically when no motion is detected. Up to 25 Wireless switches may be used to control the lights from multiple locations.

More information:

0-10 Volt Wireless Dimming Controller Tutorial

Demonstration of ILLUMRA battery-free wireless switches and occupancy sensors being linked to wireless 0-10V Area Controllers. The Area Controller features 20A load switching capacity and 0-10V dimming circuit rated to control dimming of up to 200 fixtures. The system uses wireless motion sensors to operate occupancy sensing mode with the lights turning on with motion or in vacancy mode with a manual switch and lights turning off automatically when no motion is detected. Up to 25 Wireless switches may be used to control the lights from multiple locations.

More information:

Thank You

Thank you for contacting us!

Where we go from here

If it is during business hours, we will get back to you within an hour!

If it is not during business hours, we will get back to you as soon as possible.

If you would like to reach us sooner, feel free to call us at (801) 349-1200.

Single Rocker Wireless Light Switch

Colors and Part Numbers

White.....................E9T-S1AWH

Light Almond........E9T-S1ALA

Ivory.......................E9T-S1AIV

Gray.......................E9T-S1AGY

Brown....................E9T-S1ABR

Black......................E9T-S1ABK

Description

ILLUMRA Self-Powered Wireless Light Switches are completely wireless and battery-free. They use the kinetic energy from pressing the switch to send a wireless RF signal to controllers and gateways.

Control a light fixture or one group of lights with this ILLUMRA Single Rocker Switch. This switch communicates with 902 MHz EnOcean protocol. Switches are also available in ZigBee and Bluetooth protocols. Accelerate installation of wireless controls from the planning phase to the completion with our new mobile commissioning system.

Specifications
E9T-S1Axx
Range	50-150 feet (typical)
Frequency	902 MHz EnOcean® Protocol
Power Supply	Self-generated when switch is pressed
Buttons	2 Buttons (1 rocker)
Output Channels	Only limited by number of receivers in range
Dimensions	2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature [Storage Temperature]	-13° to +149°F (- 25° to + 65°C) [-13° to +149°F (- 25° to + 65°C)]
Radio Certifications	FCC (United States): SZV-PTM215U I.C. (Canada): 5713A-PTM215U
Addressing	Factory set unique ID (1 of 4 billion)

Downloads

Applications

Wiring Diagrams

Dual Rocker Self Powered Wireless Light Switch

Colors and Part Numbers

White....................E9T-S2AWH

Black.....................E9T-S2ABK

Light Almond.........E9T-S2ALA

Ivory.......................E9T-S2AIV

Gray .......................E9T-S2AGY

Brown.....................E9T-S2ABR

Description

ILLUMRA Self-Powered Wireless Light Switches are completely wireless and battery-free. They use the kinetic energy from pressing the switch to send a wireless RF signal to controllers and gateways.

Control two lights or two groups of lights with this ILLUMRA Dual Rocker Light Switch. Each rocker can separately control an unlimited number of ILLUMRA controllers that are within range.

This switch communicates with 902 MHz EnOcean protocol. Switches are also available in ZigBee and Bluetooth protocols. See also our Single Rocker Switch.

Accelerate installation of wireless controls from the planning phase to the completion with our new mobile commissioning system.

**Specifications**
E9T-S2Axx
Range	50-150 feet (typical)
Frequency	902MHz
Power Supply	Self-generated when switch is pressed
Buttons	4 Buttons(2 rockers)
Output Channels	Only limited by number of receivers in range
Dimensions	2.75(W) x 4.5(H) x 0.62(D)inches
Operating Temperature [Storage Temperature]	-13° to +149°F (- 25° to + 65°C) [-13° to +149°F (- 25° to + 65°C)]
Radio Certifications	FCC (United States): SZV-PTM215U I.C. (Canada):5713A-PTM215U
Addressing	Factory set unique ID(1 of 4 billion)

Downloads

Applications

Wiring Diagrams

Hotel Room Controls

APPLICATIONS

Hotel Energy Savings

CASE STUDIES

Marriott Courtyard – Kapaa, Kauai

Application

Wireless Hotel Room Controls are easy to install and they will reduce energy cost up to 30%.

Scenario

Hotel Room Controls Turn off power to unoccupied rooms. Occupancy-based or Key Card based room controls reduces the energy consumption of unoccupied rooms by up to 30%. ILLUMRA Self-powered Wireless Controls help hotels comply with energy standards such as CA Title 24 and ASHRAE/IESNA standard 90.1.box]

Guests leave lights and other appliance on when not in the room

Increases energy costs
Increases maintanence cost

Solution

Illumra Wireless, Battery Free Room Contols. When using Key Card Readers, Window Door Senors or Occupancy Sensors as Hotel Room Controls they will deactiviate power to the HVAC Unit when guest removes key or there is no motion in the room.

Simple activation or deactivation by inserting or removing room key
Extend life of bulbs and mechanical equipment in room
Up to 30% energy saving achieved and Hotel Owner saves money

Products

Key Card Reader Relay / Receiver

Window Door Sensor Wall Occupancy Sensor

Wireless Room Temperature Sensor

Part Numbers

SR04
Room temperature sensor only

SR04P
Room temperature sensor with set point adjustment

SR04PT
Room temperature sensor with set point adjustment, presence key (pictured)

SR04PST
Room temperature sensor with set point adjustment, presence key, fan speed switch

SR04P MS
Room temperature sensor with set point adjustment, slide switch O/I

SR04 rH
Room sensor humidity/temperature

SR04P rH
Room sensor humidity/temperature with set point adjustment

SR04PT rH
Room sensor humidity/temperature with set point adjustment, presence key

SR04P MS rH
Room sensor humidity/temperature with set point adjustment, slide switch O/I

Description

The Room Temperature Sensor sends a wireless signal to a receiver whenever the temperature falls out of the preset range. Features include a occupancy push button and temperature adjustment knob.

Specifications
SR04xx
Transmitting Range	50-150 feet (typical)
Antenna	Type: Helix – Gain: -3dBi
Transmitting Frequency	315 MHz
Temperature Detection	Range	0°C to 40°C
""	Resolution	0.15K
""	Absolute Accuracy	typ. ±0.4K
Optional Humidity Sensor	Range	0-100% rH
""	Resolution	0.4% rH
""	Absolute Accuracy	typ. ±3% Range 30% . . . 80%
""	1 Point Callibration	50%
Optional Set Point Adjustment P	Range	0-270° Angle of Rotation
""	Resolution	1.1°
Rotary Switch S	Number of Switching Steps 5 (A- 0- I- II- III)
Slide Switch MS (optional with button T)	Number of Switching steps 2 (O/I)
Measuring Value Detection	Every 100 Seconds
Sending Interval	. . . every 100 seconds
Energy Generator	Solar cell/ internal goldcap/ maintenance-free
Enclosure	ABS (ASA) color pure white similar to RAL 9010
Protection	P20 according to EN60529
Ambient Temperature	-25°C to 65°C
Transport	-25°C to 65° C/max. 70% rH – non-condensed
Weight	1.76oz. (50g)
Radio Certifications	FCC (U.S.) – IC (Canada)

Downloads

Applications

None

Wiring Diagrams

None

Ceiling Occupancy Sensor

Part Number

E9T-OSC

Description

Ceiling-Mount Motion Sensors sense motion over a 360 degree coverage area.

Specifications	E9T-OSC
Frequency	902 MHz EnOcean RF transmitter
Transmission Range	50-100 ft. (17-33M)
Motion Detection Range	34ft. (10m) diameter @ 10ft (3m) mounting height (Refer to coverage diagrams)
Minimum Operation Light	50 lux (for auto-off only)
Charge time to full	25 hrs @200 lux
Sustaining Charge time	3 hours per 24 hours @ 200 lux
Motion Transmission Interval	2 minutes
Unoccupied Transmission	10 and 30 minutes since last motion detection
Heartbeat Transmission	default = disable / enable = 1 hr intervals
Operating Life in Darkness	80 hours (after full charge)
Optional Battery Life	Continuous battery-free operation standard; Infrequent Bright Light: 20yrs (with 200lux for 2 hrs/day 7days/week Consistent Low Light: 15 yrs (with 65 lux for 5 hrs/day 7 days/week Total Darkness: 6.5 yrs
EnOcean Equipment Profile (EEP)	A5-07-01
Dimensions	6.5" H x 2.36" W x 1.47" D (160mm x 60mm x 37mm)
Mounting Height	7-10 feet (2-3m) recommended
Agency Compliance	FCC: SZV-STM300U

Downloads

Applications

Coming Soon

Wiring Diagrams

Coming Soon

Wireless LED Dimmer Demonstration Kit

[three_fourth_last][one_third]

[box]

Wireless LED Dimmer Demo Kit

[/box]

Wireless LED Dimmer Demo Kit:

ExT-S1AWH – Single Rocker Switch

E9X-D02FL – Wireless Receiver

ExT-OSW-W – Wall Occupancy Sensor

[/one_third]

[two_third_last]

[box]Description

Experience PWM LED dimming control with a battery-free wireless switch and an occupancy sensor. Energy harvesting switches and sensors harvest mechanical and ambient light energy to operate without batteries. The PWM LED Dimmer switches 5A loads with 65,000 smooth dimming steps.

A Wireless 0-10V Dimmer Demo Kit is also available.[/box]

[table “” not found /]

[one_third]
Downloads

Switch Datasheet
Switch Installation Guide
Constant Voltage Dimmer
Constant Voltage Installation Guide[/one_third][one_third]

Applications

Commercial Lighting Control
Title 24 Wireless Lighting Control
Log Home Lighting
Landscape Lighting
(More . . .)[/one_third][one_third_last]

Wiring Diagrams

[/one_third_last][/two_third_last]

Search Results for: NS0-303 Guaranteed Passing 🚦 NS0-303 Valid Test Topics ℹ NS0-303 Valid Exam Pattern ⭐ Search for ⏩ NS0-303 ⏪ and download exam materials for free through ➽ www.pdfvce.com 🢪 👯NS0-303 Reliable Exam Pdf

Application

Scenario

Solution

Products

Request a Quote form:

Request a Quote form:

SPECIFICATIONS - BTX-DUV-OCC

Request a Quote form:

SPECIFICATIONS - BTX-D01-OCC

Private Labeling

All our products are available with your logo, so you can bundle wireless controls to sell with your fixtures.

With no effort on your part–once you’re set up–products will be shipped with your logo on the label and shipping box. The mobile app will show your logo. Setting this up is easy.

How to use the OEM Label Forms for the xUV Product Line

This document is intended to help you make labels for the Area Controller, Fixture Controller, 20 Amp Universal Relay, and Control Extender.

In order to use the OEM label form, you should first collect the following information.

The name and contact information of the person who will approve the artwork.

The ordering code you will use when selling the product.

The product details you want listed near the logo, applied to the front label as well as the box.

Your logo. It will be printed at 300dpi in a space that is .95 inches x .285 inches, or 285 x 86 pixels (W x L). The logo image should be monochrome.

The information highlighted in yellow below is the information you can customize using this form. This is an example of our area controller label.

Once you have collected the requested information, you will go to the form of the label you wish to customize.

The links are listed below:

Once all the requested information has been submitted and the logo received, we will make a digital mock up for you to approve. Once the label and artwork has been approved we will be able to use your custom label on the product.

Request a Quote form:

Illumra Distributors

USA

Canada

ILLUMRA Self-powered Wireless Door sensor Selected For “2012 Top Products Award Winners”

“2012 Top Products Award Winners”

ILLUMRA is looking for qualified manufacturer representatives.

Distributor inquiries

Press Contact

Image Gallery

Order ZigBee switches right now from Digikey:

Or request a quote from ILLUMRA, using the form below.

Request a Quote form:

Request a Quote form:

Thank you for contacting us!

Where we go from here

Request a Quote form:

Specifications

Request a Quote form:

Application

Scenario

Solution

Products

This product is discontinued.

Request a Quote form:

Request a Quote form: